rev c pol10 - 05t series 10a output current rating d c/dc open frame converter single output 1/9/2018 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? f ax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 1 of 5 smd type sip vertical mounting sip horizontal mount size: 1.30in x 0.53in x 0.30in size: 2.00in x 0.50in x 0.28in size: 2.00in x 0.50in x 0.28in options features ? smd or sip package ? vertical or horizontal mounting available for sip models ? neg ative or positive logic remote control option ? ? ? ? ? ? ? ? ? ? ? ? ? telecom/datacom ? industry control system ? distributed power architectures ? semiconductor equipment ? microprocessor power applications the pol10 - 05t series of dc/dc open frame power converters offers 10a output current rating in a small size and low profile package. this series cons ists of single output models with an operating input voltage range of 2.4~5.5vdc. each model in this series is compliant to rohs ii & reach, ce marked, has low ripple & noise, and is protected against over load, short circuit, and over temperature conditio ns. this series has ul60950 - 1, en60950 - 1, and iec60950 - 1 safety approvals. please contact factory for order details. model selection table model number input voltage range output voltage output current @full load package type no load input current 0.75 vdc/3.3vdc maximum capacitive load (1) efficiency (2) remote on/off pols10 - 05t 5vdc (2.5~5.5vdc) 0.75~3.3vdc 10a smd 100/300ma 1000/5000 f 95% positive pols10 - 05t - p negat ive polt10 - 05t 5vdc (2.5~5.5vdc) 0.75~3.3vdc 10a sip vertical 100/30 0ma 1000/5000 f 95% positive polt10 - 05t - p negative polt10 - 05ta 5vdc (2.5~5.5vdc) 0.75~3.3vdc 10a sip horizontal 100/300ma 1000/5000 f 95% positive polt10 - 05ta - p negative
rev c pol10 - 05t series 10a output current rating d c/dc open frame converter single output 1/9/2018 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? f ax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 2 of 5 specifications all specifications are based on 25c, nom inal input voltage, and maximum output current unless otherwise noted. we reserve the right to change specifications based on technological advances. specification test conditions min typ max unit input specifications operating input voltage range vout( set) , vin - 0.5vdc 2.5 5 5.5 vdc maximum input current vin=2.4 to 5.5vd, io=io(max.) 10 a input reflected ripple current 5~20mhz, 1 h source impedance 100 map - p start - up voltage 2.2 vdc shutdown voltage 2.0 vdc input filter (3) capacitor type output specifications output voltage see table voltage accuracy % of vout(set) - 2.0 +2.0 % line regulation vin=vout(set) +0.5vdc to vin(max.) at full load; % of vout(set) - 0.3 +0.3 % load regulation no load to full load; % of vout(set) - 0.4 +0. 4 % voltage adjustability (4) 0.7525 3.63 vdc remote sense 0.5 vdc output current see table maximum capacitive load see table ripple & noise measured by 20mhz bw, with a 1 f mlcc & a 10 f t/c 15 mvrms 50 mvp - p dynamic load response with a 1 f mlcc & a 10 f t/c +0.4 %/ o c rise time time for vout to rise from 10% to 90% of vout(set) 6 ms remote on/off control (5) (6) negative logic ( option ) dc - dc on open or 0 ~0.3vdc dc - dc off 1.5vdc~vin(max.) positive logic (standard ) dc - dc on open or vin(max.) dc - dc off 0~0.3vdc input current of ctrl pin 0.01 1.0 ma remote off input current 1.5 ma turn - on delay time (7) 1 ms over voltage overshoot - startup vin= 2.4~5.5vdc at full load; % of vout(set) 1.0 % protection short circuit protection continuous, automatic recovery over load protection % of iout rated 200 % over temperature protection 125 o c environmental specifications operating case tempera ture with derating - 40 +85 o c storage temperature - 55 +125 o c relative humidity 5 95 %rh thermal shock mil - std - 810f vibration mil - std - 810f mtbf mil - hdbk - 217f, full load 3,239,000 hours general specifications efficiency see table switching frequency 270 300 330 khz physical specifications weight 0.21 oz(6.0g) dimensions (l x w x h) smd type 1.30in x 0.53in x 0.30in (33mm x 13.5mm x 7.6mm) sip type 2.00in x 0.50in x 0.28in (50.9mm x 12.7mm x 7.2mm) safety characteristics safety a pprovals ul60950 - 1, en60950 - 1, iec60950 - 1 lead- free reflow solder process ipc j - std - 020d moisture sensitivity level ipc j - std - 033b, level 2a
rev c pol10 - 05t series 10a output current rating d c/dc open frame converter single output 1/9/2018 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? f ax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 3 of 5 notes (1) esr 1m / esr10m, test by minimum input and constant resistive load. (2) vin(nom), 3.3vdc @ full load (3) it?s necessary to equip the external input capacitors at the input of the module. the capacitors should connect as close as p ossible to the input terminals ens uring module stability. the external cin is 3pcs of 150f low - esr polymer capacitors // 2pcs of 47f ceramic capacitors at least. (4) output voltage is programmable from 0.75v to 3.3v by connecting a single resistor (shown as trim table) between the trim and g nd pins of the module. to calculate the value of the resistor rtrim for a particular output voltage vout, use the following equation: trim figure trim table (5) remote on/off referred to ? vin pin (6) positive logic: on/off is open collector/drain logic input negative logic: on/off pin is open collector/drain logic input with external pull ? up resistor. (7) case 1: on/off input is set to logic low (module on) and t hen input power is applied (delay from instant at which vin=vin(min.) until vout=10% of vout(set)) case 2: input power is applied for at least one second and then the on/off input is set to logic low (delay from instant at w hich von/off=0.3vdc until vout - 1 0% of vout(set)) caution: this power module is not internally fused. an input line fuse must always be used. * due to advances in technology, specifications subject to change without notice. characteristic curves pols10 - 05t, vout=3.3v derating c urve pols10 - 05t, vout=3.3v efficiency vs. input voltage pols10 - 05t, vout=3.3v efficiency vs. output load
rev c pol10 - 05t series 10a output current rating d c/dc open frame converter single output 1/9/2018 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? f ax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 4 of 5 mechanical drawing s pols10 - 05t pin connection pin define 1 ctrl 2 +sense 3 trim 4 +vout 5 gnd 6 +vin polt10 - 05t pin connection pin define 1 +vout 2 +vout 3 +sense 4 +vout 5 gnd 6 gnd 7 +vin 8 +vin 10 trim 11 ctrl polt10 - 05ta pin connection pin connection pi n define 1 +vout 2 +vout 3 +sense 4 +vout 5 gnd 6 gnd 7 +vin 8 +vin 10 trim 11 ctrl notes: all dimensions in inch(mm) tolerance: x.xx0.02 (x.x0.5) x.xxx0.01 (x.xx0.25) pin pitch tolerance: 0.01 (0.25 pin dimension toleranc e 0.004(0.1)
rev c pol10 - 05t series 10a output current rating d c/dc open frame converter single output 1/9/2018 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? f ax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 5 of 5 model number setup polt 10 - 05 t - p series name output current input voltage package remote control option pols: smd type 05: 2.4~5.5vdc t: no assembly (smd type) none: positi ve logic polt: s ip type t: vertical mounting ( sip type) p: negati ve logic ta: horizontal mounting (sip type) company information wall industries, inc. has created custom and modified units for over 50 years. our in - house research and development engineers will provide a solution that exceeds your performance requirements on - time and on budget. our iso9001 - 2008 certification is just one example of our commitment to producing a high quality, well - document ed product for our customers. our past projects demonstrate our commitment to you, our customer. wall industries, inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. we will continue to provide ongoing support for your project above and beyond the design and production phases. give us a call today to discuss your future projects. contact wall industries for further information: phone: ? (603)778- 2300 toll free: ? (888)5 9 7 - 9255 fax: ? (603)778- 9797 e - mail: sales@wallindustries.com web: www.wallindustries.com address: 37 industrial drive exeter, nh 03833
|
